Qualification Test on Digital Height Gauge MACHINE OPERATION 厚度規設備操作認證測試

The test is designed to test the understanding of the staff in this training.

本測試的目的是為測試員工對培訓的理解程度。

Please write down the correct answer in the space. All questions should be answered.

請在空格內填寫正確答案，必須全部作答。

TEST DURATION測試時間 :15MINUTES 15分鐘

基本信息：

姓名：
流程：
員工編號:

1. （） What can Digital Height Gauge machine be used for?
厚度規機器可以用來測量什么?

A. Paper thickness 紙厚度B. SR Thickness綠油厚度C. Photo Resist Thicknesss光刻膠厚度D. All the above以上所有

2. （） What is the accuracy of the thickness gauge machine?
厚度規機器精度是多少?

A. 0.1mmB. 0.01mmC. 0.001mmD. 0.0001mm

3. （） How to adjust the range of a thickness gauge?
厚度規如何調節量程?

A. Adjusting the thickness gauge measuring pointer調節厚度規測量指針B. Adjust the position of the measurement sample調節測量樣品位置C. Adjusting the rear support rod調節后面的支持桿D. Replacing measurement samples更換測量樣品

4. （） How to use thickness gauges?
厚度規如何使用?

A. Zero the reading將讀數置零B. Lift the measuring pointer，place the sample on the measuring table抬起測量指針，將樣品放在測量臺C. Lower the measuring pointer and check the reading放下測量指針，查看讀數D. All the above以上所有

5. （） Where is the power switch located?
開關鍵在哪里?

A. Control Panel 控制面板B. On the side of the Thickness gauge 厚度規側面C. Joystick 控制桿D. PC keyboard 電腦鍵盤

6. （） What to pay attention to when using thickness gauges?
厚度規使用要注意什么?

A. Turn on the switch, it can only be used when the switch is turned on打開開關，開關開啟方可使用B. Check if the calibration is qualified before use查看校準是否合格，校準合格方可使用C. The measuring pointer should be handled gently測量指針要輕拿輕放D. All the above以上所有

7. （） What are the measurement criteria?
測量準則是什么?

A. Measure multiple times, calculate the average value, and reduce errors多次測量，求平均值，減小誤差B. Fast, accurate, and ruthless快、準、狠C. Accurate, fast, and efficient準確、快速、高效D. One measurement is sufficient測量一次即可

8. （） What are the reading criteria?
讀數準則是什么?

A. Take a casual glance隨意瞟一眼B. Multiple readings多次讀數C. Read again after the reading stabilizes待示數穩定后再讀數D. Reading when the reading jumps示數跳動時讀數

9. （） Which of the following is not the measurement unit of the thickness gauge?
下面哪個不是厚度規的測量單位?

A. Micron微米B. Millimeters毫米C. Centimeters厘米D. Square centimeters平方厘米

10. For multiple multi-point measurements, the "zero" bit should be confirmed regularly.
多次多點測量時，應定時對“歸零”位確認。

A. Yes 是B. No 否

更多問卷復制此問卷

感谢您访问我们的网站，您可能还对以下资源感兴趣：

久久97中文字幕

亚洲成A人V欧美综合天堂麻豆孩交av免费观看久久AV片免费一区二区三精品无码国产中文一区二区